Twincat issue

Keep Open and Learning
Post Reply
jiataifeng
Posts: 178
Joined: 30 Apr 2009 06:31

Twincat issue

Post by jiataifeng » 12 Oct 2018 21:42

Safety problem like attached below:
solution
1. find your serial number at SAFETY->safe project -> target system, update the hardware address if necessary.
2. select your safety project and and verify it in the Winsafe menu.
3. then download safety project and type in the credintial you got like this.

credintial:
username:Administrator
serial number:1228819
password:TwinSAFE



Error 9 11/10/2018 3:24:29 PM 474 ms | 'Drive 22 (AX5203-0000-0210) (Chn A)': 0x F415, Distributed clocks: Process data synchronization lost
Error 10 11/10/2018 3:24:29 PM 474 ms | 'Drive 17 (AX5140-0000-0210) (Chn A)': 0x F415, Distributed clocks: Process data synchronization lost
Error 11 11/10/2018 3:24:29 PM 474 ms | 'Drive 22 (AX5203-0000-0210) (Chn B)': 0x F415, Distributed clocks: Process data synchronization lost
Error 25 11/10/2018 3:28:48 PM 047 ms | 'TCNC' (500): 'Mandrel' (Axis-ID: 3): The axis respectively the drive is not enabled/ready for positioning (error-code: 0x4225) !
Error 26 11/10/2018 3:28:48 PM 047 ms | 'TCNC' (500): UASv (ID 3, CmdNo=2, 1 (Bufferd), CurPos=-0.000002, CurVelo=0.000000, CurAcc=0.000000) StartPos=-0.000002; EndPos=1e+15; Velo=0.416667; Acc=3.000000, Dec=3.000000, Jerk=10.000000, Error=0x4225
Error 27 11/10/2018 3:28:48 PM 047 ms | 'TCNC' (500): 'Mandrel' (Axis-ID: 3, Grp-ID: 3): Group function is rejected with error-code 0x4225 or the function is not supported !
Error 28 11/10/2018 3:28:49 PM 337 ms | 'TCNC' (500): 'Mandrel' (Axis-ID: 3): The axis respectively the drive is not enabled/ready for positioning (error-code: 0x4225) !
Error 29 11/10/2018 3:28:49 PM 337 ms | 'TCNC' (500): UASv (ID 3, CmdNo=2, 1 (Bufferd), CurPos=-0.000002, CurVelo=0.000000, CurAcc=0.000000) StartPos=-0.000002; EndPos=1e+15; Velo=0.416667; Acc=3.000000, Dec=3.000000, Jerk=10.000000, Error=0x4225
Error 30 11/10/2018 3:28:49 PM 337 ms | 'TCNC' (500): 'Mandrel' (Axis-ID: 3, Grp-ID: 3): Group function is rejected with error-code 0x4225 or the function is not supported !
Last edited by jiataifeng on 12 Oct 2018 21:55, edited 3 times in total.

jiataifeng
Posts: 178
Joined: 30 Apr 2009 06:31

Beckhoff FB_DBConnectionOpen bBusy is always true.

Post by jiataifeng » 12 Oct 2018 21:43

There is a problem with Twincat Database Server(TF6420 Database Server). try to uninstall it and reinstall.

Post Reply